Instructions for paints, Eggshell

SATIN WATER-BASED PAINT. EXTERIOR AND INTERIOR. CERTIFICATIONS. ENVIRONMENTALLY FRIENDLY

Description

Mono-component water-based polyurethane enamel with very high performance and high opacity.

 

Formats

  • 125 ml. / 1,25 m2
  • 750 ml. / 7,5 m2

 

Properties

  • Pleasant to the touch and very smooth.
  • Excellent levelling of characteristics similar to classical synthetic products.
  • Highly resistant to abrasion and rubbing.
  • Resistant to the damaging effects of the outdoors.
  • Good adhesion on diffcult surfaces.
  • Does not yellow over time.
  • Resistance to household cleaning products.
  • Does not contain organic solvents.
  • Low odour and VOC content.
  • Interior and exterior application.

Uses

Exterior and interior. Advisable for lacquering wooden doors and windows. Protection of a large variety of surfaces (duly primed) such as wood, plaster and iron, galvanised, aluminium, PVC, stainless steel.

 

Technical Data

  • Appearance: glossy
  • Colour: white and colours from the chart.
  • Density 20ºC (kg/l): 1.22 ± 0.05
  • Content in solids % volume: 40
  • Fire Resistance classification (EN13501-1): A2-s1-d0
  • Yield (m²/L): 8- 12, in dry thickness of 35-50 microns.
  • Touch dry (hours): 1-2
    Second coat (hours): 5-6
  • Thinner: water
  • % brush or roller dilution: 0-15
    % spray gun dilution: 10-20
  • Cleaning of utensils and stains: with water before drying.
  • Volatile Organic Compounds (COV): maximum product content 37,00 g/l.

 

How to apply

  1. Stir the product until totally smooth.
  2. The surfaces to be painted must be clean, dry and free of dust, grease, saltpetre, etc.
  3. If the surface is already painted, ensure the previous paint is in good condition and well-adhered.
  4. We recommend thinning the paint with water according to technical data epigraph.
  5. Test compatibility between coats (shades and specification matters).

 

Surface and ambient conditions

  • Ambient temperature: do not paint at a temperature of below 7°C.
  • Surface temperature: the surface temperature should be 2 – 3 ºC above dew point when painting.
  • Relative humidity: never apply with relative humidity exceeding 80%.
  • Ambient conditions: the paint should not be applied under conditions of excessive sunlight, strong winds, or if rain is forecast.

 

Surface preparation

UNPAINTED SURFACES:

  • Concrete: removal of product residues and foreign substances. Must be properly sanded and, after removing all dirt, apply a suitable base coat according to the table of possible painting systems and sand gently. Then apply two coats of finish, sanding gently between layers.
  • Aluminium: if the surface is enamel coated, the existing enamel layer should be removed with paint stripper. Paint as if it were a new unpainted surface.
  • Wood: removal of product residues and foreign substances. Must be properly sanded and then all dirt is removed. It is advisable to apply 1-2 coats of wood filler to regulate surface absorption.If subsequent protection is required it is advisable to apply a coat of protective base coat before applying the wood filler.
  • Iron and Steel: remove any existing mill scale. Remove any rust or rusted material (by sandblasting or scraping and mechanical or manual brushing), until a rust-free surface remains. Apply 1 or 2 coats of anti-rust primer according to instructions given in the possible application systems.
  • Galvanised: if the surface is enamel coated, the existing enamel layer should be removed with paint stripper. Paint as if it were a new unpainted surface.

 

PRE-PAINTED SURFACES IN GOOD CONDITION:

  • Aluminium: if the surface is enamel coated, the existing enamel layer should be removed with paint stripper. Paint as if it were a new unpainted surface.
  • Wood: thoroughly sand the previous paint in good condition. If protection is desired, it is advisable to apply a bottom coat to an open pore before applying the wood filler.
  • Concrete: remove elorescences, product residues and foreign substances (grease, dust, oils and/or derivatives, etc.). To seal porous concrete it is advisable to use a suitable sealant according to the table of possible application systems.
  • Iron and Steel: eliminate high alkalinity and regulate absorption by applying a suitable fixer/primer Remove elorescences, product residues and foreign substances (grease, dust, oils and/or derivatives, etc.).
  • Galvanised: if the surface is enamel coated, the existing enamel layer should be removed with Paint Stripper. Paint as if it were a new unpainted surface.

 

Possible applciation systems

Use a brush, roller or spray gun for normal application of Eggshell. At least two top coats are recommended. Prior to the top coat and depending on the wall apply primer suitable for the yield specified in each case.

 

PRIMERS:

  • Solvent-based acrylic sealer or Acrylic primer in solution.
  • Aqua siloxane sealer or siloxane acrylic primer.
  • Opaque acrylic primer (promotes adhesion and an absorption regulator for mineral substrates).

 

MATT-INTERIOR FINISH:

  • Yield: 8-12 m2/L.
  • Coats: 2

Safety

Unsuitable for children. Keep out of the reach of children. Do not place painted surfaces into the mouth.

 

Removal

Take the necessary measures to ensure waste is kept to an absolute minimum. Analyse all possible methods for reuse or recycling, in line with the local and national legislation in force. Take the necessary measures to ensure waste is kept to an absolute minimum. Analyse all possible methods for reuse or recycling. Do not pour down drains or into the environment. Dispose of the product at an authorised waste disposal site or through an authorised waste management company. Waste must be handled, stored and disposed of pursuant to current local-national legislation.

 

Storage

Store the containers away from high temperatures, direct exposure to the sun and frost. Maximum recommended storage time: 12 months from manufacture in fully sealed original container, indoors and at temperatures between 5º and 35º C.

 

Legal text note

This information and, in particular, the recommendations regarding the application and final use of the product, are given in good faith, based on the current knowledge and experience of Coordonné of the products when they are properly stored, handled and applied, in normal situations, within its useful life, according to the recommendations of Coordonné. In practice, the possible dierences in the materials, supports and actual conditions at the place of application are such that it cannot be inferred from the information in this document, no any other written recommendation, neither any advice oered, will insure the guarantee in terms of marketing or suitability for particular purposes, neither any obligation outside of any legal relationship that may exist. The user of the products must carry out the tests to verify their suitability according to the use they want to give. Coordonné reserves the right to change the specifications of its products. The property rights of third parties must be respected. All orders are accepted according to the terms of our current General Conditions of Sale and Supply. All orders are accepted in accordance with Coordonne’s terms and prices. Users must understand and use the latest version of the technical sheet available at coordonne.com. Data on this sheet are based on laboratory tests. The measures taken “on site” may vary due to circumstances beyond our control.

We are here to support you

Do you wish to know more about a fabric?
Get in touch with our team, through contacts
or our online assistant.

Subscribe to our newsletter