WATER-BASED MATTE. INTERIOR.
CERTIFICATIONS. ENVIROMENTALLY FRIENDLY.

Description

Matte plastic paint of excellent quality, extraordinary whiteness and covering. Respond all the requirements established in the “GREEN BUILDING”.

Formats

• 125ml = 1,25m2
• 1 litre = 10 m2
• 4 litres = 40 m2

Properties

• Pleasant silky feel.
• High washability.
• Resistance to wet rubbing.
• Good adherence.
• Does not turn yellow with time.
• Odourless and low in VOCs.
• Indoor application.

Uses

Specially suitable for painting walls and ceilings, indoors, where high quality finishes are required.

Technical Data

• Appearance: Matt
• Colour: white and colours from the chart.
• Finish: Matt
• Thinner: Water
• Viscosity (Brookfield RVT at 20ºC).
• Poises: 180 – 220
• Density a 20ºC (Kg/l): 1.53 ± 0.05
• Content in solids % volume: 42
• Gardner washability (UNE 48284) (dp): More than 10,000 cycles.
• Wet scrub resistance (UNE-EN ISO 11998): Class 2
• Opacity (ISO 6504-3): class 1 for a yield of 6 m²/litre corresponding to 2 coats of paint.
• Yield (l/m²): 10-16
• Touch dry (20ºC) (min): 30
  Second coat (hours): 3 to 4
  Total drying (days): 15 to 20
• % brush or roller dilution: 0-5
  % spray gun dilution: 5-15
• Cleaning of utensils and stains: with water before drying.
• Volatile Organic Compounds (COV): maximum product content 0,70 g/l.

How to apply

1. Stir the product until totally smooth.
2. The surfaces to be painted must be clean, dry and free of dust, grease, saltpetre, etc.
3. If not, the surface must be cleaned properly and prepared with a coat of appropriate fixer.
4. If the surface is already painted, ensure the previous paint is in good condition and well-adhered.
5. We recommend thinning the paint with water according to technical data epigraph.

Surface and ambient conditions

• Ambient temperature: do not paint at a temperature of below 7°C
• Relative humidity: never apply with relative humidity exceeding 80%.
• Ambient conditions: it is not recommended to paint in rainy weather or at times of peak heat.

Surface preparation

UNPAINTED SURFACES:

• Cement mortar: elimination of elorescence and alkalinity by treating with diluted zinc sulphate. Regulate absorption by applying a suitable fixer/primer.
• Plaster/Cast plaster: apply one coat of fixer/primer to create a foundation of resin, allowing breathability, reducing absorption and facilitating the subsequent application of paint.
• Concrete: wait until completely set (min. 30 days). Removal of stripping substances. Regulate absorption with the application of a suitable fixer/primer.
• Fibre cement: eliminate high alkalinity and regulate absorption by applying a suitable fixer/primer.

PRE-PAINTED SURFACES IN GOOD CONDITION:

Regardless of the support to be repainted, its appearance must be homogenised; in other words, adjust the surfaces that are shiny to help to open the pores and foster adhesion. Check the adhesion and resistance of the paint. Correct any texture or planimetry differences that may exist with repair mortars. Test compatibility between coats.

PRE-PAINTED SURFACES IN POOR CONDITION:

• Diseased: surfaces with mould and algae: Removal and disinfection of mould or algae by vigorously rubbing the stain with a brush using household bleach or 10 volume hydrogen peroxide.It is finished with two finishing coats with anti-mould preservative for film protection.
• Surfaces with metal salts: these, coming from the slabs, are reddish or yellowish in colour; they must be covered with two coats of suitable anti-stain paint and then painted as normal.
• Brittle: ff the paint is old or badly adhered with defects such as chalking, blistering, peeling, cracking, etc., it must be completely removed and then apply a coat of transparent acrylic fixer.

Possible applciation systems

Use a brush, roller or spray gun for normal application of COBLANC. At least two top coats are recommended. The first coat should be diluted 15-20% and the second coat should be diluted 5-10%, always with clean drinking water. Prior to the top coat and depending on the wall apply primer suitable for the yield specified in each case.

PRIMERS:

• Solvent-based acrylic sealer or Acrylic primer in solution.
• Aqua siloxane sealer or siloxane acrylic primer.
• Opaque acrylic primer (promotes adhesion and an absorption regulator for mineral substrates).

MATT-INTERIOR FINISH:

• Yield: 10-16 m2/L.
• Coats: 2

Safety

Unsuitable for children. Keep out of the reach of children. Do not place painted surfaces into the mouth.

Removal

Take the necessary measures to ensure waste is kept to an absolute minimum. Analyse all possible methods for reuse or recycling, in line with the local and national legislation in force. Take the necessary measures to ensure waste is kept to an absolute minimum. Analyse all possible methods for reuse or recycling. Do not pour down drains or into the environment. Dispose of the product at an authorised waste disposal site or through an authorised waste management company. Waste must be handled, stored and disposed of pursuant to current local-national legislation.

Storage

Store the containers away from high temperatures, direct exposure to the sun and frost. Maximum recommended storage time: 12 months from manufacture in fully sealed original container, indoors and at temperatures between 5º and 35º C.

Legal text note

This information and, in particular, the recommendations regarding the application and final use of the product, are given in good faith, based on the current knowledge and experience of Coordonné of the products when they are properly stored, handled and applied, in normal situations, within its useful life, according to the recommendations of Coordonné. In practice, the possible dierences in the materials, supports and actual conditions at the place of application are such that it cannot be inferred from the information in this document, no any other written recommendation, neither any advice oered, will insure the guarantee in terms of marketing or suitability for particular purposes, neither any obligation outside of any legal relationship that may exist. The user of the products must carry out the tests to verify their suitability according to the use they want to give. Coordonné reserves the right to change the specifications of its products. The property rights of third parties must be respected. All orders are accepted according to the terms of our current General Conditions of Sale and Supply. All orders are accepted in accordance with Coordonne’s terms and prices. Users must understand and use the latest version of the technical sheet available at coordonne.com. Data on this sheet are based on laboratory tests. The measures taken “on site” may vary due to circumstances beyond our control.